PV Tracker Bearing & Bushing Solution

Solar Tracker Bearing Housing

A maintenance-free, self-lubricating bearing for solar tracker torque tubes. Available for octagonal, square and custom shaft profiles, with self-alignment support for uneven terrain, installation deviation and long-term outdoor operation.

  • Maintenance-free & self-lubricating
  • Up to ±20° alignment compensation
  • Low friction, wear and operating noise
  • Drawing-based OEM customization
solar tracker bearing housing installed on green uneven terrain
solar tracker bearing housing installed on uneven terrain
Octagonal • Square • Custom Integrated housing and bushing solution for utility-scale PV tracker structures.
±20° Reference self-alignment / offset compensation
-40°C to +60°C Reference outdoor operating temperature range
>15,000 Reference test rotations from current model data
Custom OEM 2D drawing, 3D model or sample-based development
Related solutions
solar tracker bushing bearing for solar tracker torque tube bearing housing wear resistant bushing PV tracker custom bearing housing solar tracker

Product Overview

Maintenance-Free Solar Tracker Bushing for Uneven Terrain

The bearing housing is designed for low-speed, high-load tracker movement where foundation height, post position or torque-tube alignment may vary. Its self-centering structure helps the tracker adapt to installation deviation while supporting smooth rotation and stable long-term operation.

custom bearing housing solar tracker application
Designed around real tracker installation conditions Uneven terrain • mounting deviation • outdoor exposure • low-speed rotation

Why It Matters

Reduce Resistance, Motor Load and Installation Risk

  • 01
    Automatic alignment compensation The self-centering bearing position can adapt when foundations or support posts create installation error.
  • 02
    Lower rotational resistance Low-friction bushing performance helps reduce starting torque and unnecessary motor loading.
  • 03
    Reduced jamming risk Improved tolerance to shaft deviation helps minimize binding caused by imperfect field installation.
  • 04
    Fast integrated installation Lightweight molded construction supports easier assembly, fewer maintenance points and efficient project installation.

Performance Advantages

Built for Long-Term Outdoor PV Tracker Operation

The housing and bushing material system is selected to balance structural strength, impact resistance, dimensional stability, low friction, wear resistance and outdoor durability.

Low Friction

Self-lubricating contact surfaces support smoother low-speed movement with reduced friction and noise.

Wear & Impact Resistance

Suitable for repetitive movement, dusty sites and demanding mechanical conditions with strong impact energy absorption.

UV & Corrosion Resistance

Material formulation can include antioxidant and UV-stabilizing support for outdoor exposure and corrosive environments.

High Dimensional Stability

Glass-fiber-reinforced housing helps maintain strength, rigidity and fit across temperature changes and long service periods.

Installation Error Compensation

How the Self-Aligning Torque Tube Bearing Housing Works

Field foundations and tracker posts are not always perfectly aligned. The bearing assembly allows controlled angular compensation so the torque tube can find a more suitable working position instead of forcing the drive system to absorb the full installation error.

Step 01 Installation deviation occurs

Foundation elevation, support-post position or torque-tube geometry creates a small angular mismatch.

Step 02 The bearing self-centers

The internal bearing position adjusts within its allowed range to support the actual shaft alignment.

Step 03 The tracker rotates more smoothly

Reduced binding helps lower drive torque, motor load, local stress and the risk of long-term jamming.

Material System

Self-Lubricating Bushing + Reinforced Polymer Housing

The final resin grade, reinforcement, stabilizer package and dimensional tolerances can be reviewed according to load, shaft profile, operating temperature, UV exposure and project lifetime requirements.

Bushing Material

HMWPE-Based HPA020 Bushing

A modified high-molecular-weight polyethylene bushing material developed for low friction, impact energy absorption and wear resistance in demanding outdoor motion applications.

Low coefficient of friction Smooth low-speed rotation
High impact resistance Absorbs mechanical shock
Chemical resistance Acids, alkalis and corrosive gases
Outdoor stabilizers Antioxidant and UV support
Housing Material

PA66-GF30 Reinforced Housing

Glass-fiber-reinforced PA66 provides a practical balance of strength, rigidity, surface quality, dimensional stability and corrosion-free performance for tracker support structures.

High tensile strength Structural support under load
Dimensional stability Reliable fit across temperature change
Low water absorption option Reduced dimensional change
Injection-molded consistency Repeatable batch production

Torque Tube Compatibility

Solar Tracker Bushing Options for Octagonal and Square Shafts

Standard reference models are available for common tracker torque-tube profiles. Custom interfaces, mounting holes, wall thickness and bearing dimensions can be developed from your drawings.

Octagonal Shaft Bearing

Designed around common octagonal torque-tube profiles used in single-axis solar tracker structures.

Reference model: ZQ121BS Custom profile available Self-aligning

Square Shaft Bearing

Suitable for square torque tubes with project-specific clearance, wall thickness and mounting requirements.

Reference model: ZQ120SS Custom dimensions Low-friction bushing
ModelShaft TypeHousing MaterialBushing MaterialReference Test LoadReference Test RotationsAbrasion LossOffset AngleTemperature Range
ZQ121BSOctagonalPFL26 / PA66-GF30HMW HPA020700 lb>15,0000.87 g±20°-40°C to +60°C
ZQ120SSSquarePFL26 / PA66-GF30HMW HPA020700 lb>15,0000.65 g±20°-40°C to +60°C

Reference data shown above is based on the current model information supplied for this page. Final values, tolerances and test methods should be confirmed in the approved technical datasheet for each project.

Application-Focused Solutions

Choose the Right Bearing Housing for Your PV Tracker Project

The product can be configured for different torque-tube shapes, loads, site conditions, service temperatures and tracker assembly requirements.

Self-Lubricating Bushing Solar Tracker

For projects requiring reduced lubrication work, low friction and consistent low-speed motion.

Wear Resistant Bushing PV Tracker

For dusty, high-cycle or mechanically demanding sites where abrasion control is important.

Maintenance Free Bearing Solar Tracker

For utility-scale installations seeking fewer service points and lower long-term maintenance effort.

Custom Bearing Housing Solar Tracker

For non-standard torque tubes, mounting interfaces, project tolerances or drawing-based OEM programs.

OEM Manufacturing Support

Solar Tracker Bearing Housing Manufacturer & Bushing Supplier

As a solar tracker bearing housing manufacturer and solar tracker bushing supplier, we support project communication from initial drawings through material review, tooling, sample confirmation and batch production.

Drawing Review

Send a 2D drawing, 3D model, torque-tube profile or physical sample for an initial feasibility review.

Material & Tolerance

Confirm load, offset, temperature, UV exposure, fit, wall thickness and key inspection requirements.

Tooling & Sample

Prepare tooling, produce samples and verify assembly, rotation, dimensions and project-specific performance.

Batch Supply

Coordinate production, inspection, packaging and delivery for repeat OEM solar tracker programs.

Frequently Asked Questions

Solar Tracker Bearing Housing FAQ

Key questions for tracker manufacturers, EPC companies, component distributors and sourcing teams.

What is the difference between a solar tracker bearing housing and a solar tracker bushing?

The housing provides the structural mounting interface, while the bushing is the low-friction wear component contacting or supporting the torque tube. They are engineered together to control alignment, load transfer, friction and service life.

Can the torque tube bearing housing compensate for installation deviation?

Yes. The self-aligning structure is designed to accommodate controlled angular offset, helping the shaft find a more suitable working position when foundation elevation or support-post alignment is not perfect.

Can you customize the bearing for solar tracker shaft dimensions?

Yes. Octagonal, square and non-standard torque-tube profiles can be reviewed from your 2D drawing, 3D file or sample. Mounting holes, interfaces, clearances, wall thickness and material selection can also be customized.

Is this suitable as a maintenance free bearing solar tracker solution?

The self-lubricating polymer bushing is intended to reduce routine lubrication requirements and maintenance points. Final suitability depends on load, movement cycle, contamination, temperature and approved project validation.

What information is needed for a quotation?

Please provide the torque-tube drawing or profile, shaft dimensions, expected load, required offset angle, mounting interface, operating temperature, estimated annual quantity and any material or test standard.

Do you support prototypes before mass production?

Yes. Sample production and assembly verification can be arranged before batch manufacturing, subject to drawing review, tooling requirements and project schedule.

REQUEST A QUOTE

Upload Your Drawing. Get a Fast Quote.

Send CAD files or samples for evaluation. Quote & DFM suggestions within 12 hours (Mon–Fri). NDA available.

What to Send

STEP/IGES/STP/PDF/DWG + qty + material + surface finish

What You Get (12h)

Cost breakdown + lead time + DFM suggestions

Confidential & Reliable

NDA available. Files kept confidential.

Request a Quote

Send drawings or samples. We’ll reply with a quote and DFM feedback.

拖拽文件到此处,或者
Accepted file types: stp, step, igs, iges, pdf, dwg, dxf, stl, zip, rar, Max. file size: 256 MB.
    REQUEST A QUOTE

    Upload Your Drawing. Get a Fast Quote.

    Send CAD files or samples for evaluation. Quote & DFM suggestions within 12 hours (Mon–Fri). NDA available.

    What to Send

    STEP/IGES/STP/PDF/DWG + qty + material + surface finish

    What You Get (12h)

    Cost breakdown + lead time + DFM suggestions

    Confidential & Reliable

    NDA available. Files kept confidential.

    Request a Quote

    Send drawings or samples. We’ll reply with a quote and DFM feedback.

    拖拽文件到此处,或者
    Accepted file types: stp, step, igs, iges, pdf, dwg, dxf, stl, zip, rar, Max. file size: 256 MB.